Monday July 21 2008
Letter Re: Pre-Assembling Charity Food Packets for Storage
JWR –
I am putting together food stores, and collecting food grade buckets for bulk storage (local store lets them go for 60 cents each), but I had a question come across as I was planning this out.
Based on my own sense of charity, as well as your comments, I thought about a self-contained package that could be handed out, some rice, wheat, dried veggies and more, all sealed with a gamma lid using your dry ice method. Not only would this be good to avoid having multiple bulk cans open at once, but also as I said if people in need come asking, you can hand of 3-to-5 days food in one package.
Then I started thinking about comfort foods, pretzels, chips, candy bars and the like, and I wondered if you can actually put all of these different food products in the same can, separated into baggies, and if so, can you keep some foods like pretzels/chips or candy in their original packaging or repackage them in baggies? - Geoff in North Dakota
JWR Replies:
Using separate clear plastic baggies--or better yet mylar bags--within a sealed container is a practicable solution.
Distributing whole wheat is only marginally workable, since most folks are used to baking with wheat flour. But this raises two issues: If distributing flour, does the recipient have access to a working baking oven or Dutch Oven? In most disaster situations, that would be a rarity. And, if distributing while wheat, does the recipient have a access to a wheat grinder. Of course you could instruct them to make wheat berries (soaked wheat to eat as hot or cold cereal). But then they must have water available and at least 10 hours to soak the wheat. Because of the much shorter shelf life of flour (versus whole wheat), you might consider packaging the wheat in the form of freshly-ground flour, only on an "as-needed" basis, after the onset of an emergency.
Letter Re: Satellite Images and Your G.O.O.D. Route
Hi James,
While they are still available, now might be a good time to use one of the satellite image sites (like Google Earth) to download and print out detailed satellite images of planned bug-out routes. Having those images with you during a bug-out strikes me as a great way save time and energy by knowing exactly where important survival-related features are located. For example, my own route includes a stretch of rather barren territory with no lakes or streams shown on the topo map, but the satellite images show ponds and small reservoirs too small for inclusion by the map makers. As they may only be seasonal irrigation ponds I wouldn't want to depend on them, but at least I would know where to start looking, if it became necessary. The images also show features that flat maps only approximate. And, while nothing takes the place of actually checking the route personally before it is needed, one could take a "virtual walk" of their route to get an idea of what they might encounter, and adjust their plans accordingly.
My prayers are with your wife for a speedy and full recovery. My best, - John in Colorado
Letter Re: Springfield Armory XD Pistol Accessories
James-
I wanted to thank you for the great web site! It's fantastic!
I was on the Springfield Armory web site yesterday, and noticed that they are having a 20% off sale on all accessories, including XD magazines, through July 31st. I picked up four more, and thought I'd pass the info along.
Keep up the great work, and I pray for a healthy recovery for your wife. - Kristopher in Afghanistan
JWR Replies: Thanks for your prayers for The Memsahib. We are now hopeful that she will make a complete recovery.
I am enthusiastic about the XD pistols. Now that spare parts for the XD pistols are available, they are my top pick for self defense pistols.
An important reminder to all SurvivalBlog readers in North America: Front Sight's Gun + Gear + Training special offer (that includes a free XD pistol in your choice of calibers) will be ending soon, so don't hesitate!
Odds 'n Sods:
I was recently doing a web search on "Asymmetric Warfare" and I came across this interesting article (in PDF) from Military Review magazine in 2001: America's Frontier wars: Lessons for Asymmetric Conflicts.
o o o
Reader Michael H. suggested this article from Bob Chapman's The International Forecaster: The Formula For Hyperstagflation
o o o
Trent H. sent us a link to an article summarizing a recent speech by Congressman Ron Paul: "Some Big Events Are About To Occur"
o o o
Pyotr in the Czech Republic wrote me to mention that he was researching custom-built intrusion detection systems for rural retreats, and he found this interesting reference: Perimeter Security Sensor Technologies Handbook.
Jim's Quote of the Day:
"If ... ...Fannie and Freddie are flat-out taken over entirely by the US government (and remember the Federal Reserve is not the government), then the national debt will roughly double overnight -- which will pound the US dollar down a rat-hole." - James Howard Kunstler
Sunday July 20 2008
Letter Re: Rampant Inflation in Steel Products
Hey Jim,
I used to make my living as a construction electrician and had several big steel Greenlee brand tool boxes with my tools. There is usually one in the back of my
truck all the time.
Price of gun safes has continued to rise, so I took one of my boxes and cut out a plywood rack for my guns, then filled in around the rack with polyurethane foam. After it was set and cured, I painted the urethane foam flat black.
The fit and finish on my Greenlee tool box/gun safe is good enough to protect my weapons, keep them locked and secure. It also has the advantage of handles and skids so it can be loaded into a pickup or bug out trailer to get to the remote retreat in a hurry. If necessary, I can load it with a forklift, or a chain hoist, or muscle it on with three other men.
Anyway, I thought you might be interested in my improvised gun safe.
The steel tool boxes can still be bought from Lowe's [hardware store] for $199. Regards, - Lawrence, editor of SurvivingTheDayAfter@yahoogroups.com
JWR Replies: Thanks for that cost-saving suggestion. Just keep in mind that "portability" works both ways. It is essential that you secure your vault, box, or chest to a floor or a very sturdy wall, to prevent burglars from hauling off "The Whole Shebang." Be sure to use heavy duty lag bolts!
Letter Re: A Reminder to Readers About Botulism
I think that the author of "Letter Re: A Reminder to Readers About Botulism" [posted on July 18th] is a little mistaken about the deadliness of "even a single small whiff of Botulinum toxin." The video in the link he provided is a discussion of the effects of weaponized botulism toxin. In the video, it's stated that botulism doesn't make a very good open-air weapon, although it may have potential as a weapon in enclosed areas or by infecting food.
According to the Botulism Handbook for Epidemiologists, Clinicians, and Laboratory Workers:
...botulism can be picked up by (a) eating contaminated food, (b) through intestinal colonisation in infants fed contaminated-honey (though apparently not in adults fed the same honey), and (c) through open wound contamination when cleaning up contaminated surfaces or substances. In a later section, it states that "Botulinum toxins are extremely poisonous for humans. Minute quantities acquired by ingestion, inhalation, or by absorption through the eye or a break in the skin can cause profound intoxication and death;" however, I believe that in this section, they are referring to refined botulism toxin in a laboratory environment.
On the CDC "Botulism > Botulism Associated with Canned Chili Sauce, July 2007 > Questions and Answers" page, they describe the cleanup procedure for suspected or known-contaminated canned food as follows:
Do not open or puncture any unopened can of the recalled product.
Dispose of food that may be contaminated by placing in a sealable bag, wrapping another plastic bag around the sealable bag, and then taping tightly. Place bags in a trash receptacle for non-recyclable trash outside the home and out of reach of humans and pets. Do not discard the food in a sink, garbage disposal, or toilet. Avoid splashing and contact with the skin. Wear rubber or latex gloves when handling open containers of food that you think may be contaminated. Wash hands with soap and running water for at least 2 minutes after handling food or containers that may be contaminated.
Wipe up spills using a bleach solution (use 1⁄4 cup bleach for each 2 cups of water). Completely cover the spill with the bleach solution. Place a layer of paper towels, 5 to 10 towels thick, on top of the bleach. Let the towels sit for at least 15 minutes, then put the paper towels in the trash. Wipe up any remaining liquid with new paper towels. Clean the area with liquid soap and water to remove the bleach. Wash hands with soap and running water for at least 2 minutes. Sponges, cloths, rags and gloves that may have come into contact with contaminated food or containers should be discarded with the food.
While extreme care should be taken to limit exposure to contaminated food, including immediate disposal, wearing rubber gloves, and surface cleanup with bleach, again, the CDC doesn't seem to be advocating the use of a respirator or warning to avoid breathing in "even a single small whiff" of the air from the can. Botulism is dangerous, but a botulism-contaminated food source is unlikely to kill you unless you touch it with an open wound or ingest some of the food. That said, I probably wouldn't try and sniff around a bulging can of bad food; but if I did, and later suspected botulism, I wouldn't be terrified I might die, either. - M.C.P.
Odds 'n Sods:
Thanks to Eric B. for potting this: Study shows fuel cell cars still 15 years away at best
o o o
SF in Hawaii forwarded this video link: Jim Rogers Speaks the Truth about Fannie Mae and Freddie Mac
o o o
Wolf sent us this: Merrill Drops After $4.65 Billion Second-Quarter Loss, the same day that Cheryl sent us this: Citigroup posts $2.5B loss, but beats expectations. It seems neither the brokers nor the banksters are faring well in this credit-starved environment.
o o o
JT flagged this one from The Daily Telegraph: Africa's Oil Boom Shifts Balance of Power
Jim's Quote of the Day:
"We are not what we know, but what we are willing to learn." - Mary Catherine Bateson
Saturday July 19 2008
Note from JWR:
I'm posting things early today, since we are going in to town where The Memsahib will be seeing the doctors. Thanks for your many e-mails of support and your continuing prayers.
Letter Re: The Tomato Rebuild--Machining Technology is Crucial to Modern Society, by Thomas G.
Jim,
After reading the recent letter by Thomas G, I felt compelled to offer a response to demystify some of the technologies he talked about. First, I am a tool and die maker for an ammunition manufacturer. If it's broken, I fix it, if we need it, but can't buy it, I design and make it.
From reloading dies, case feeders, powder measures, primer feeders, cold header press parts, I have done a lot. So I feel somewhat qualified to shed some light onto how things are done. I'll start basic, and then work up to complex.
Aside from the technology of making metal, the most basic component is arguably the screw, or the nut and bolt. While these can be made on a lathe, that's simply not practical in the world of mass production. Since at least the turn of the previous century (1800-1900) bolts have been made using machines called headers and rollers. Headers come in two forms, cold and hot. A cold header is typically used for making bolts, these take wire (and by wire, I mean form, not size) the wire is then cut, and pushed into a die. A forming die will then come down and crush the wire that sticks outside the base die, this forms the bolt head, this can also be done for nails, rivets, screws etc. In the case of bolts and screws they are then dropped into a thread rolling machine. This is a device which has two panels which have flattened threads cut onto them, the bolt rolls between the two panels and is threaded.
Nuts are made by hot-heading. A slug of wire is heated until it's pliable, and is then smashed into a form. When it's cooled it's then threaded using a tap.
Gears are made on machines called hobbers, but can be made on a horizontal mill, or a shaper with an indexing head. The hobber works by holding a gear blank between centers, and then has a cutter that rotates above the gear. Once a gear is made, it can be used as a template for casting more, either die cast, or sand cast, depends on size and material.
A lathe is a fairly basic machine, if anyone has ever seen a wood lathe, a metal lathe works on the same principle. If you can build a wood lathe, you can build a metal lathe in a number of iterations. Given the scrap available from even a post-collapse society cobbling a functional lathe together should be fairly easy. The same applies to a mill.
For those who have interest, I suggest checking out the gingery machines web site, and perhaps even buying the book set. While a long time ago I decided it was easier to buy and rehab an old lathe than to build a new one, the books will give even the novice user a good idea about how machines are made.
It is important to note that most machine tools were conceived back in the 1800s. With a few decent measuring tools, almost anything can be made. The greatest thing about the age we live in currently is our ability to measure. If you have a few decent sets of dial calipers, a few dial indicators, a pyrometer (for heat treating) and a stop watch, you can produce just about anything you need.
At times after reading "Patriots" I laugh at the [refugee] character who was the machinist, (Lon Porter) since he carried his tools around in a bicycle trailer. While one tool box may satisfy the storage space required for some measuring tools, it would take a truck to move all of the various tools (tool bits, drill bits, mills, punches, indicators, angle finders,
etc) that I would consider ideal for a post-apocalyptic machine shop.- AVL
Letter Re: PetroMax Kerosene Lanterns
Hi Jim,
I figured I’d better write about my experience with PetroMax (BriteLyt) Kerosene lanterns.
I’ve had their 150CP (Candle Power) (100 watts of light) for a couple years now and really like it.
BriteLyt is now providing their 500CP (400 watts of light ) to the US Government as Model MR-2 with a federal stock number.
BTW they also make a nice 11,000 BTU kerosene stove which they are also making for the government.
So I got two of the new USG MR-2s and tried them out. Right away I had a problem!
As you know, I’m [living and own a retreat at] at 6,600 feet MSL and 9,800 feet MSL. (I should have picked up on this earlier. Altitude! Lack of air! Ha!) Okay, sometimes I can be slow witted.
Anyway, I had a miserable time of it with these two lamps. If I’d have been at sea level, I wouldn’t have had any problems.
Working with BriteLyt, I used the jets for their 150CP lamp and now the MR-2s series work great at my altitude. I’m going to try their 350CP jets (a little bigger gas flow) and see how they work. More light should be the result. Actually, I like the way the 150CP jets work.
How great are these lamps? Really great.
Nice light! Absolutely. [Because of the intense glare,] I highly recommend the lampshade style reflector.
Burn anything. Gasoline, Paint thinner, kerosene, diesel, JP-8. What do you have, I’d probably try it in these lamps.
The word I’ve got from my research worldwide is “If you have a PetroMax that works well, it’ll be a thing of joy for a lifetime.”
BTW, repair parts are really inexpensive and worth putting in a supply if you get these lamps. As you know, the [US] military has geared up for exclusively JP-8 and done away with gasoline, except for those darned never-worked-right gasoline lamps. Now one more thing is JP-8 capable. A lantern that burns JP-8 diesel.
I heard we had some boys freeze to death in Afghanistan last year and the inclusion of the kerosene stove will make sure that doesn’t happen again. With the kerosene stove in a pit under a tent or tarp, you’re not gonna freeze.
All in all, for a good prep, I recommend these lamps. However, as with all technology, toy with them and learn the little quirks that they have. Overall, I’m well pleased especially with the [large quantity of] diesel I have put away.
I’ll update you when I get the 350CP jets and also when I can get one of their stoves. - The Army Aviator
Odds 'n Sods:
Thanks to Cheryl for sending a link to an article that describes how more banks are in trouble. These include: Wachovia (downgraded on the 15th), WaMu, National City Corp., and U.S. Bancorp
o o o
Eric sent a link to an editorial from The Des Moines Register: Help farmers, consumers: Revive grain reserve
o o o
KMA spotted an article in The Economist titled Peak Oil, The Only Way is Down.
o o o
John T. sent us a link to an article that is a sign of the times: Pakistani Investors Stone Exchange as Stocks Plunge
Jim's Quote of the Day:
"If you ever hear a government official come out and say that an institution is fine, you know it's time to get your money out because history shows they're likely lying. Look what happened with Fannie and Freddie. The government said everything was fine right up to the day the US Treasury dropped the biggest government bailout of all time on the American taxpayer. The bill for Fannie, Freddie and the bank failures could cost the taxpayer over $400 billion. (That's your money, of course.)". - Richard Benson in: Is Your Money Safe?
Friday July 18 2008
Note from JWR:
The high bid in the current SurvivalBlog Benefit Auction is $500. This auction is for a big mixed lot: a NukAlert radiation detector, donated by KI4U--a $160 value), a DVD of 480 E-books on Alternative Energy (donated by WK Books--a $25 value), and the following package of survival gear all kindly donated by CampingSurvival.com: One case of MREs, one pack of water purifications tablets, a bottle of colloidal silver, a fire starter, a bottle of potassium iodate tablets, an emergency dental kit, a pack of "Shower in a bag" bath wipes, and one messenger bag to pack it in.
Letter Re: A Reminder to Readers About Botulism
Jim,
Feel free to post the following if you think it would be of help and interest.
Bulging cans with botulism are worse than most think. While bulging cans of food are relatively rare and most everybody knows that any bulging can should be discarded, few know just how seriously dangerous they can become if opened or accidentally ruptured. Botulism is so extremely deadly, it must be suspect in all bulging cans and they must not only be discarded, but put away from anyone else. Botulinum toxin is one of the most lethal substances known to man, as seen in this CDC article. When food is in short supply some will begin buying and using whatever old cans they can find and be eager not to waste anything too, thus many will also be tempted to open suspect bulging cans to better inspect the contents, before just rejecting it, and usually by smelling it.
People need to know that even a single small whiff of Botulinum toxin, especially when concentrated and released from a pressurized bulging can, can kill you stone dead in a few paralyzing hours, it's truly that deadly. Please warn people at every opportunity to never fool with any suspect cans and to dispose of them as if a live grenade, where no one will come across them either. - Shane Connor, www.ki4u.com
Letter Re: The Cost of Things to Come
We are in a simultaneously deflationary and inflationary situation.
The deflationary forces are:
1) We've been a credit based society and with less credit available, less purchasing will happen driving down prices.
2) Most people have most of their wealth in their home, their stocks and their banks (Indy Mac anyone?), all decreasing in value thus putting the brakes on discretionary purchasing driving down prices.
The inflationary forces are:
1) The rising price of oil raises transportation and manufacturing costs for everything.
2) The increasing population and decreasing supply of commodities (food, metals etc.) increases prices.
3) The Fed cannot raise the interest rate and slow down inflation without causing an even worse housing collapse.
With two opposite forces pulling on the economy, for a time we have had a dynamic stasis as the forces balanced each other. Now these two forces are literally tearing the fabric of the economy asunder.
On one side, anything available that is sold in the international marketplace or has intrinsic value will increase in price.
This means food, oil, ammo, metals, commodities. This is due to the loss of the value of the dollar and the fact that the demand for these items is less negotiable. On the continuum, you must have food, and you'd really like not to freeze this winter due to lack of heating oil.
You, along with six billion other people will do what you have to, in order to continue to eat but do you really need that 40" television, a dinner out or a vacation or...
Anything that is sold exclusively locally (not including commodities), and is discretionary will begin to decrease in price.
Expect deep discounts as stores that do not have international presences liquidate inventory to cover expenses. Have you been to [shop at] The Sharper Image lately?
This includes anything that people own and don't really need such as: Trucks, cars, boats, electronics etc...
Consider what you do for a living. If you have hard skills (plumbing, gardening, medical), your skills are non-discretionary. You will be needed and your prices can rise with the prices of commodities.
If you are a consultant, artist, analyst, if you have a store that sells non-essentials, you're vocation is discretionary. Your prices will likely go down if you want to attract work.- SF in Hawaii
Letter Re: The Backwoods Home Magazine Anthologies
Jim,
I recently purchased Backwoods Home's "The Affordable Whole Shebang" offer which includes printed anthologies of Backwoods Home starting from year one to the present (13 years) as well as 11 CD-ROMs packed full of information: recipes, alternative energy, firearms info, preparedness guide, etc. The CD-ROMs include a partial electronic anthology of the magazine (years 7-14) for easy portability.
I was very impressed by the sheer volume of reading material for only $257! I am a voracious reader and it will take quite a while for me to consume it all. I highly recommend this fantastic offer and feel that not only is it entertaining to read, it is very informative as well. This is an important addition to the preparedness library. I'm not associated with the magazine--just a satisfied reader. - Rob M.
Odds 'n Sods:
Downturn gains steam as inflation roars ahead
o o o
Cheryl N. sent us this: Fears Over Safety in Savings Triggers Panic in US
o o o
Jason M. flagged this: ‘Flying IEDs’ Pose New Iraq Threat. (OBTW, I've had the acronym "UAVIED" in the SurvivalBlog Glossary since August of 2005. Terrorists may soon use radio-controlled planes--from the size of light model planes, on up--packed with explosives.)
o o o
The International Forecaster anticipates "A Complete and Systemic Breakdown" of the US and world financial systems and economies. (Kudos to Kevin A. for finding that item.)
Jim's Quote of the Day:
"Today is the day you swore was going to be different - yesterday." - Nick Murray
Thursday July 17 2008
Note from JWR:
The high bid in the current SurvivalBlog Benefit Auction is $390. This auction is for a big mixed lot: a NukAlert radiation detector, donated by KI4U--a $160 value), a DVD of 480 E-books on Alternative Energy (donated by WK Books--a $25 value), and the following package of survival gear all kindly donated by CampingSurvival.com: One case of MREs, one pack of water purifications tablets, a bottle of colloidal silver, a fire starter, a bottle of potassium iodate tablets, an emergency dental kit, a pack of "Shower in a bag" bath wipes, and one messenger bag to pack it in.
A July, 2008 Jim Rawles Interview by AlterNet
The following is a transcript of an interview that will soon be run at the popular left-of-center AlterNet web site:
AlterNet: Is survivalism a failure of community? A celebration of it?
JWR: I'd say that survivalism is indeed a celebration of community. It is the embodiment of America's traditional "can do" spirit of self-reliance that settled the frontier.
AlterNet: Is it engineered by personal issues? Is it a racial, or economic phenomenon, in your opinion? Or both?
JWR: Survivalism [is a movement that] crosses all racial and religious lines. It is essentially color blind. For 99% of us, we could care less about the color of someone's skin, but we care a lot about about including people with valuable skill sets. The preparedness movement is simply a rational quest for family and community level self-sufficiency in an increasingly dangerous world. There is unfortunately a very small but very vocal minority that are disgustingly racist idiots. I'm sad to say that they also call themselves survivalists. They get an inordinate amount of press coverage, making that 1% look much larger than it really is. In my opinion they should be ignored and shunned, and I certainly don't give them a platform on SurvivalBlog.
The economic cross section of SurvivalBlog readers is also amazing. We have working class readers that a worried about how they are going to make their next car payment posting alongside surgeons and entrepreneurs. We have both starving students and Little Old Lady pensioners. The readership is also global. We have regular readers in more than 90 countries. But even with this diversity, we all get along. [I didn't mention that I also edit out a lot of rants and foul language from the readers' letters that I post.] Part of this is the realization that the next Great Depression will be a tremendous "leveler".
AlterNet: Do you think survivalism is a rational response to our current crises?
JWR: Absolutely.
AlterNet: After all, we have an administration with minority support that is ruining the economy and world without a care for what its majority thinks. Do you think the unilateral policies of America over the last several years has contributed to the mindset? Or is it just gun nuts going too far?
JWR: There is greater interest in preparedness these days because the fragility of our economy, the lengthening chains of supply, and the complexity of the technological infrastructure have become apparent to a broader cross-section of the populous. All parties concerned may not realize it, but the left-of-center Greens that are calling for "local economy" and encouraging farmer's markets actually have a tremendous amount in common with John Birchers that are decrying globalist bankers, and likewise with gun owners that complain about their constitutional rights being trampled. At the core, for all of them, is the recognition that big, entrenched, centralized power structures are not the answer. They are, in fact, the problem.
AlterNet: What do survivalists get right?
JWR: They recognize that smaller scale economies and older technologies are appropriate. They also recognize that meaningful solutions are found at the community level--not from top-down, command-driven bureaucracies.
AlterNet: What do they get wrong?
JWR: A minority of SurvivalBlog readers are over-enamored with gadgets. I call these folks "Mall Ninjas." They live in a fantasy world. In the real world, skills beat gadgets every time. But in our "big box" consumerist economy, some people mistakenly think that they can buy happiness, or--in this case--buy preparedness. A big, expensive pile of "tacticool" gear without the hard-earned skills to know how to use it is essentially useless. It takes time and a requisite expenditure of sweat to really know how to tend a garden, hang a gate, cut a cord of firewood, or field dress a deer. Some people have simply never done something so basic as digging a post hole in rocky ground, and they will break down in tears if they ever have to. Their fancy gear can't do everything for them.
AlterNet: Do you think Peak Oil and climate crisis will team up to smack the American Dream down?
JWR: I think that Peak Oil is already upon us, but I'm reserving my opinion on climate change, since there is so much conflicting evidence.
AlterNet: Do you think technology can save us?
JWR: I don't think that technology--in and of itself--can save us. Again, it is practical skills, not gadgets that will help us to pull through tough times. This not to say that I don't recommend some high tech items like photovoltaic panels. Life without them in a "grid down" situation would be very uncomfortable. I'm also a great fan of hydrogen fuel cell, alcohol gas, and biodigester technologies. But those will likely be a case of "too little, too late." If anything, life in the 22nd Century will more closely resemble the 19th Century than it will the 20th Century. I predict that it will be a century of steam and horse power. And between now and then? Sadly, the 21st Century will probably be remembered as the time of the Great Die-Off.
AlterNet: Are Americans too spoiled to change their ways before it is too late?
JWR: For some Americans, yes. But others are clearly showing the wisdom to "Get Out of Dodge" while the getting is good, by moving to lightly-populated "retreat" regions to genuinely pursue self-sufficiency. Again, these people come from all across the political spectrum. I think that in the the next couple of decades we will witness the formation of some remarkable intentional communities (a.k.a "gulches") that will feature some unlikely bedfellows: Anarchists and Ayn Rand readers, Mennonites and gun enthusiasts, Luddites and techno-geeks, fundamentalist Christians and Gaia worshippers, tree huggers and horse wranglers. We welcome them all. I have been pleasantly surprised to see SurvivalBlog readers set aside some very sharp differences for the sake of a common goal. That consensus is one of the things that gives me the most pride about SurvivalBlog. I'm a conservative Christian but that doesn't mean that I'm not willing to listen to a leftist agnostic, if he has something useful and productive to say about practical preparedness and self-sufficiency.
AlterNet: And what do you see as the chief threats legitimizing a survivalist defense?
JWR: The threats are clearly manifold: Peak Oil, a derivatives meltdown, pandemics, economic instability, food shortages, stock market and currency collapses, terrorism, bank runs, state sponsored global war, rationing, and more. In a situation this precarious I believe that it is remarkably naive to think that mere geographical isolation will be sufficient to shelter communities from the predation of evildoers. I strongly believe in turning the other cheek, but as a realist, I also believe in Rule 308. (See the SurvivalBlog Glossary.)
AlterNet: What are you [personally] preparing for?
JWR: All of the above. I read Psalm 91 regularly. I encourage AlterNet readers to take a look at the SurvivalBlog "Precepts" page for the details of my philosophy and envisioned scenarios. Again, I believe that we have more in common than we have differences.
Letter Re: Insect-Free Long Term Food Storage
Jim.
I have been buying flour and corn meal in five pound bags and placing in the freezer for a couple of weeks to destroy any "nits" still in them, and after that putting them in plastic bins. I really have no idea if this works long term, but would appreciate any suggestions on whether or not there is any method to preserve these items other than this. I have a Porkett hand grinder, but to grind wheat fine enough for bread flour is difficult. Thanks, - Charlie P.
JWR Replies:
Just freezing the grain doesn't kill all the insect eggs, which can hatch later. You need to use either dry ice (CO2) or oxygen absorbing packets, (the latter available from Nitro-Pak and several other Internet vendors), to get a 100% kill of adult bugs, larvae, and eggs. I've posted details of the dry ice method a few time in SurvivalBlog. It is also described at in my "Rawles Gets You Ready" preparedness course and in Alan T. Hagan's Food Storage FAQ.
You also asked about wheat grinders. To grind fine flour, I recommend the Country Living grain mill, available from Ready Made Resources and several other Internet vendors. It is an excellent mill, designed for a lifetime of use. We have one here at the ranch. It is a hand mill, but because its driving wheel has a V-belt ("fan belt") slot, it can be easily converted to be powered by an electric motor, a bicycle, or even a water wheel or windmill.
Odds 'n Sods:
Reader Robert V. mentioned a news service report on the recent bank run in California.
o o o
From Yahoo! Finance, What if my bank fails? Some questions and answers. (A hat tip to Kevin A.)
o o o
Outfitters Supply (one of our advertisers) is offering SurvivalBlog readers free freight on all wall tents and wall tent frames, which is a savings of at least $29 and up to $240 for a full tent package. Mention that you are a SurvivalBlog reader and they will deduct the freight charges.
o o o
Paul B. sent a Bloomberg article quoting investment guru Jim Rogers. Paul's comment: "I'm amazed at how many of your observations seem to dovetail into 'professional' investors' take on the economy. Jim Rogers, one of the most successful investors in the last 20 years, outlines in clear terms what is happening in the current financial world."
Jim's Quote of the Day:
"It only took a sinking dollar, US$4 gas, sky-rocketing food inflation, pathetic employment numbers, a limping stock market, and a housing crash for the mainstream to start to question our dominance. But apparently, we're there." - Kathlyn Von Rohr, writing in the Sovereign Society's Offshore A-Letter, July, 2008
Wednesday July 16 2008
Notes from JWR:
Congrats to JJW, the high bidder in the recent SurvivalBlog Benefit Auction. Today we begin a new SurvivalBlog Benefit Auction. This one is for a big mixed lot that includes: a NukAlert radiation detector, donated by KI4U--a $160 value, a DVD of 480 E-books on Alternative Energy (donated by WK Books--a $25 value), and the following package of survival gear all kindly donated by CampingSurvival.com: One case of MREs, one pack of water purifications tablets, a bottle of colloidal silver, a fire starter, a bottle of potassium iodate tablets, an emergency dental kit, a pack of "Shower in a bag" bath wipes, and one messenger bag to pack it in. The opening bid for this combined lot is just $70.
The following is another article for Round 17 of the SurvivalBlog non-fiction writing contest. The writer of the best non-fiction article will win two valuable four day "gray" transferable Front Sight course certificates. (Worth up to $4,000!) Second prize is a copy of my "Rawles Gets You Ready" preparedness course, generously donated by Jake Stafford of Arbogast Publishing. Round 17 ends on July 31st, so get busy writing and e-mail us your entries. Remember that articles that relate practical "how to" skills for survival will have an advantage in the judging.
The Tomato Rebuild--Machining Technology is Crucial to Modern Society, by Thomas G.
Have you ever really thought about your food? The intricate system that conveys it to your fingertips, and often to your mouth directly? The complicated processes and machinery that make everything run so smooth? You mat be amazed at the phenomenally complicated process involved in bringing that jug of milk, candy bar, or perhaps a simple tomato to your feast. This is an abbreviated sequence with the express purpose of shedding light on a dwindling craft: Machine work. While this trade is flourishing around the world, we here at home have swept it under the rug in favor of cheap imports and strip malls. This may soon come back to bite us. And it will be hard.
Try this illustration. After wandering about the store, pick up a tomato. Average sized, normal red, no cuts no bruises, Nothing special right? Wrong. Start hefting the tomato, looking at it from all sides, studying it with more fascination than could possibly be warranted for "just a tomato". After a while start thinking... How did this get here? And why is it so similar to all the rest, sitting here in a box along with hundreds of brothers neatly packed inside?
Well, never rejecting the oddball challenges, lets begin to think backwards through the process. The last thing that was done was a store clerk rolled it out there on a pallet jack with twenty other boxes. Hmmm... pallet jack. A small hydraulic jack whose piston and cylinder have been turned on a lathe to an exact specified size, then precision ground to within a couple of ten thousandth parts of an inch. Take your average sized hair, divide it up long ways thirty equal times, that is near .0001" or one ten thousandth part of an inch. The valve housing was drilled and tapped and cut to size in a fixture on a milling machine. The whole pallet jack was fabricated and welded up by skilled craftsmen. Wow, that is intense, and its just the tip of the iceberg! What else is not as simple as it seems? Lets keep going.
Well, it got here in a big semi truck. The trailer may have been built from extruded aluminum. The extrusion dies having been cut on a Computer Numerical Controlled (CNC) milling machine, The pistons of the large diesel have been precision turned on a lathe to about plus or minus .0005 inches. Then placed in a mill and given its flat sides, and the precision bored hole for the wrist pin. The dashboard of the truck was made by the injection molding of plastic.) The mold being cut from a large chunk, or billet, of high grade tool steel on a CNC machine cutting in three axis simultaneously, (X, Y and Z) The entire truck is assembled with nuts, bolts screws and rivets, Every one of these came off a screw turning lathe, most likely somewhere in Taiwan or Mainland China. Each one of the 18 wheels was cut from a big billet of forged aluminum on a large CNC lathe. The gears, the axles, the bearings, everything goes back to a machine tool at some point.
So, at the plant, these tomatoes ran through the gauntlet of an enormous system of computerized cameras to check for color, size, blemishes and sugar content, along with washing waxing and labeling machines. All this is achieved on miles of conveyor belts running on thousands upon thousands of rollers axles, gears, bearings, mechanical fingers and arms, motors, and actuators. Every gear was cut on a lathe for its outside diameter, and later to a four axis (X Y Z and A) indexing mill to cut each tooth. Every one of these parts had to be machined on a machine tool directly or molded from a machine tool cut mold.
Need I even mention the intricacies of a modern combine harvester being a combination of a tractor, harvester, conveyor and loading system, and sometimes even packaging plant?
The manufacturing world is based completely on the interchangeability or parts derived from the accuracies of modern metalworking machinery, and their machinists.
One of Man's claim for dominance in this world, besides being Children of God, is the use of tools. The machine tool is the pinnacle. These tools solve innumerable problems, such as building the machines to process tomatoes, looms to make cloth, printing presses for publications, molds for cups... The list goes on almost without end. But unlike power looms, printing presses or tomato processing machinery, the machine tool is self replicating. Meaning that if you have a lathe and a milling machine, you can build yourself another lathe and milling machine to continue solving more problems and conceivably create more machine tools. Can a loom build another loom?
So, TEOTWAWKI, Now what?
Remember how machine work and most other skilled work like it have been pushed aside by cheap imports? Here comes the big bite. The inability of the US to import enough basic "stuff." Oil, machine tools, computers, medical equipment, sponges, toothpicks etc... combined with our lack of an industrial infrastructure to take up the slack will result in, well, nothing. And that will last for a long time, until we re-build that infrastructure.
Modern US manufacturing is dependent on CNC machines. In a grid down/EMP situation, all this incredibly productive machinery will be completely 100% worthless, except as scrap. Although scrap is very valuable, it is not directly valuable as a machine tool. Without their computers, stepper and servo motors, glass scales (for precise measurement), and especially without tons of power, these amazing machines can not function. You can't even take the motors off the axis and put hand wheels in their place because all the measurement is digital.
China, India, and other developing nations will not fall as far back as we will during a global crisis. They're not nearly as dependent on others for their basic commodities. For example they make their own basic fasteners, their own hand tools, and basic human necessities, nearly everything. Including and especially machine tools. Also, they do more work by hand, scraping, honing, lapping, and filing. These are basic metalworking operations that can be key in machine tool fabrication. The US has lost most of the people who know these skills. These I can think of only three machine tool makers who still construct machines here. HAAS, Hardinge, and Moore. Probably a couple more, but not many. In the US this is becoming a lost art.
Third world countries rely more heavily on manual machine tools, which have integral mechanical position indicators. This is key for our infrastructure to be rebuilt, the manual machine tool. As stated earlier, most CNC machines will become boat anchors without their multitude of motors, computers, hydraulics, pneumatics. Oh, did I mention the tons of electricity to run it all? Not so with manual machine tools. The vast majority of manual machine tools have their position displayed on or near the hand wheels that power their feed and position axis. Notice the words hand wheel. Generally these machines rely on a motor to turn the spindle only. Other functions, many times, are powered off the spindle. This gives much more ready access to their belts, gears and motors, and it can conceivably only take one belt to power the whole setup. This makes these machines much more inclined to operate on alternative energy sources, such as hand cranks, leather belts and steam (or Lister) engines, bicycle chain and pedals, foot treadle, windmill, waterwheel, etc... Most can live without compressed air, hydraulics and digital readout displays. As an example, I have recently cut special round and buttress formed threads while pushing the lathe spindle around by hand.
These threads were not your ordinary 1/4-20 from your local Ace Hardware. I had to grind the shape into the high speed steel (HSS) tool bit by hand. The tools simply did not exist in any metalworking catalogs. This is the next key. The fundamental most basic cutting tool is a hard flat rock. Something to sharpen and form cutting tools and others. In its basic form it is a flat rock. In an advanced form it is a pedestal grinder. We won't discuss the more advanced types. Since there will be conceivably very few to nobody selling cutting tools, and postal services not likely, these will need to be fabricated in-house. Find an antique hand crank grinder at an antique shop or on eBay. Many still have years of life left. Many have no life left. It is a crap shoot. I've purchased two, one old and one brand new. The brand new one from India was worse than the old worn out one which I had already disposed of. Possibly a better solution, and much less of a gamble, will be to modify our existing pedestal grinders. This is quite simple, as they have standard sized shafts, and they have bearings inside. (Good grinders spin for minutes after power is removed.) Simply buy a small pulley the same size as your grinder spindle from mcmaster.com for about $4, and replace one grinding wheel with it. This can be hooked up to a big pulley with a hand wheel and any number of other alternate energy sources. Try and get a 6-to-1 ratio or more. The pulley can be put in place when the Schumer hits the fan and the grinder is still serviceable in our modern world. Very useful machine tool - Done.
Now that we've got a grinder, what are we going to grind with it? Well, to make the best tools, obviously tungsten carbide is ideal. This offers incredible rates of metal removal and lasts much longer than HSS, so it is truly the best. Oh wait, hold on, our machines may have trouble reaching the thousands of revolutions per minute necessary for tungsten carbide to cut properly without chipping and breaking. Carbide is brittle and hard, it chips and shatters at the slightest mistake. Carbide is also very difficult to re-sharpen, partially due to the fact that it needs special green silicon carbide grinding wheels that last 1/3 as long as your standard gray aluminum oxide wheels. Also, that most is in the form of disposable inserts means they wont be available anywhere. [JWR Adds: So stock up!)
High speed steel will be king in these days. The benefits of HSS for survival are; It is cheap, HSS is 5 to 50 times less than carbide. I just priced HSS blanks at kbctools.com from $0.90 to $10. People tend to think of them as strictly for a lathe. Not so, as we shall see. They are re-sharpenable with the ubiquitous gray aluminum oxide wheel. Depending on how dull they have become, smooth rocks like a whetstone or sandpaper, may work. They can be re-sharpened for more than 2/3rds their entire length! As long as you can get a bite on them with your tool holder, it is long enough. It also uses slower speeds than tungsten carbide. Its called "High speed steel" because back near the early part of the 20th Century when it was developed it was a huge advance over what people were then using - high carbon steel. This is the steel used for files, chisels, punches, and other heavy duty uses. This is the next option when the High speed steel is all depleted. It just needs slower speeds and feeds.
Much of the above pertains to both the basic lathe and milling machine. Now specifically though for the milling machines. A milling machine normally uses what is called an end mill. An end mill looks similar to a drill bit but cuts not just at its point, but on its sides as well. These kinds of cutters will be great to have, but they will run out eventually too. The great difficulty in the manufacture of these cutting tools is prohibitive to reproduce in hard times. It takes a highly complex system of grinders, usually CNC, and we all know how useful those will be after these huge solar flares coming in 2011-to-2013. Manual re-sharpening is very complex, and still involves a complex machine tool with air bearing helical indexing fixtures and grinding wheels. For example, a cheap end mill sharpener costs $4,000. Luckily all is not lost with the mill. It is possible to use a milling machine with cutters ground out of the same HSS blanks used primarily for the lathe. (Or, when push comes to shove, hardened high carbon steel) All they need is to be mounted in special holder called a fly cutter.
A much more survival style machine than the milling machine is the obsolete and no-longer produced metal shaper.
This is not like a modern woodworking shaper. This machine can make flat surfaces, grooves, T-slots, and internal and external key ways. (Internal is near impossible with a mill.) This tool pushes a cutter across the surface of the workpiece much like a wood plane cuts. No rotation of the tool or workpiece. It makes incremental steps across or down the workpiece for flats, grooves, etc. The great benefit is that it uses the same HSS blanks as your lathe turning tool and mill fly-cutter. This machine can use very simple cutters to make very complex details and shapes.
More extremely basic tools necessary for survival metalworking are files. These tools have been around since 1200 B.C. in Egypt. Their manufacture is difficult when not mechanized. Its manufacture was even shrouded in secrecy by the file-makers guilds for hundreds of years because they were such a valuable tool. Just think, blacksmiths, gunsmiths, clock makers, and locksmiths have made guns, locks clocks and precision movements for centuries with the most rudimentary of metalworking tools; a forge, and a file. With enough practice and knowledge, even making taps and dies is possible by filing.
Hacksaw blades are not necessarily super old tech, but they are just about the only hand powered way to cut thick sections of metal. These will cut through most materials, but they take time, which there ought to be plenty of again.
Taps, dies and drill bits are all going to be worth their weight in gold. Consider "roll form" taps. They don't cut the metal, they push the metal around and make the threads. They are all the rage in machine shops for a reason - they last a long time and seem to never wear out.
Find yourself an old fashioned egg beater style drill. It's mighty hard to turn a drill bit by hand through any material, even plastic and wood. Again, I haven't found any new[ly manufactured] ones that are worth considering.
Buy reprints of out-of-print books on old time skills from Lindsay Books. These classic books teach old fashioned basic skills from homesteading, blacksmithing, metal casting, steel making, boiler making and producer gas (extensively used back in the thirties to power automobiles, now usually called syn-gas or underground coal gasification) all the way to machining, wind generators, electronics, and backyard ballistics. Incredible resource at decent prices. You'll love them. Get your own copies.
If your budget permits and all your other supplies are already together, consider a small lathe and mill from kbctools.com or grizzly.com. Both companies send out free toy, ahem, tool catalogs. Also, most used machine tools are still very serviceable, and in larger metropolitan areas there are machine tool re-builders. They can make a machine like new again. They posses many of the useful skills to restart the precision metalworking economy.
If you have interest in learning the machining trade, even as a hobby, you might consider a junior college class in machine tools. The machines are not self explanatory. Most levers and handles are not labeled and you will really hurt yourself without proper training. Encourage your kids to at least give machine shop a try. We need them.
I recently heard a machinist of 30 years explain this to his co-workers. This is an example of how we are losing our manufacturing knowledge base, and how not to encourage your kids to try machining.
"I put a bottle of beer and a set of micrometers [a precision measuring instrument representing machining] in front of my son. I told him to pick one, but if he takes the micrometers, I would hit him over the head with the beer" This stems from direct competition from overseas and the accompanying shrinking profit margins. All the pressure goes straight to the shoulders of the machinist. Lower wages and lots of "Hurry up!"
In an economic depression, my reasoning tells me that people won't buy new. But they will need the old repaired, and that takes replacement parts. Cuba, because of the trade embargo, has a fleet of 1950s-vintage cars looking fine and running well because they make all their own replacement parts. This is done with machine tools and skills. In a total rebuild, we'll need everything again.
Those who are knowledgeable and posses those tangibles, HSS blanks, lathes, mills drills, taps, dies, files, hacksaws, shapers (if you can find one) and non-digital precision measuring equipment are possibly set to become wealthy. If nobody else can do it, and it doesn't come from China anymore, then where will it come from? Machine shops, machinists, welders, and blacksmiths.
In summary:
-- Our modern society rests upon machinists and their tools. Everything traces back to a machine tool.
-- CNC machines are worthless without huge amounts of energy (50 to hundreds of Amps at 220-440 VAC)
-- Manual machine tools will be our best shot because of integral measuring and ease of using alternate energy. They often have one motor and will be easier to use leather belts et cetera.
Letter Re: .22 Rimfire Conversion Kits for SIG-Sauer Centerfire Pistols
Dear Jim:
Recently, I purchased a .22 conversion kit for my SIG P226 .40 S&W pistol. I was not aware that SIG was making such a unit until I saw it in the gun shop. Although pricey, ($369 factory price, $315 store price, [and I] managed to get one for $295) I went ahead and bought it.
I can happily report that this conversion worked flawlessly out of the box. While I did not have the opportunity to really test it for accuracy, I was able to bounce a pop can around at fifty yards. The three kinds of ammo used were CCI Stinger, Remington Golden hollow point, and Remington Thunderbolt with the angular bullet. In firing approximately 90 rounds (all there was time for), there were no malfunctions.
The conversions are made for the P220, P226, P229R, and P228/229. I tried to put the unit on my [SIG Model] and [Model] 229, but it wouldn't fit, (darn!). My employer is looking at purchasing the 229 kits training. We were using a K22 for shooters that were having problems. With the price of ammo, it makes no sense to keep throwing expensive ammo into the backstop, when you can drop back to a .22, work through a problem, and move back to the larger caliber.
With this unit, you keep the trigger pull of the original pistol, unlike the SIG Mosquito [,22 LR], which has a horrible DA trigger. I was told at an armorer's class in November of 2007 that the trigger was mandated by California law. Further, I was told that SIG had no plans to bring out a conversion. I guess they
1 comment:
I go through your post and I found the very inseparable information, i am very appreciate that. Further detail visit on this Link Press Brake Forming
Post a Comment